Windswept Kishu Shimpaku

20170310_183912
Before
20170312_112442
After

I acquired a new tree, a kishu shimpaku, from Bob Pressler discussed here. I had wired most of the tree during the recent Bonsai-a-thon but was unable to style it until now.

I’ve had a few major wiring projects this past winter but for the most part have little experience shaping junipers. That said this project proved particularly challenging and took me a fair amount of time to set on a design path and execute it.

My criteria for styling the tree was as follows:

  • Use as much of the tree as possible
  • No grafting
  • Good silhouette and structure not dependent on foliage

In short I wanted the best design possible utilizing the qualities of the tree. With that in mind I had several options. Semi-cascade and windswept were the obvious ones with literati if I wanted to get really creative. Literati required that I have a good trunk line and interesting movement. I’m not the best with virts but they do call me the MS paint master. Here are the main trunks highlighted:

juniper trunk line

For literati I could remove and jin the larger lower trunk utilizing the top one. The trunk line seemed interesting enough but I lacked good branch options. Overall it would be a difficult design to pull off and would entail removing most of the tree. Plan scrapped!

I went back to drawing board. I wanted to do windswept but I was extremely cautious in doing so. Based off images of windswept bonsai and actual tree I found it crucial that the “windswept” quality be conveyed in every part of the tree–from the trunk line, branches, and the foliage.

Here is a nice article with images discussing this point: Bonsai Bark Windswept Critique

I was not confident in pulling it off so ultimately (at that time) I decided to run with semi-cascade. I began wiring out the lowest layer of branching and all looked good. Then I ran into a huge dilemma. Everything in the mid section was extremely leggy. I looked into folding the apex over itself or other hefty bends but new changes constantly led to new compromises. It was looking grim.

I then asked myself how could I utilize these leggy branches in my design? I recalled in many images of windswept trees branches oriented towards the wind would be swept back–not only lending interesting movement, but effectively shortening the branch. Here is an image uploaded by Boon with a juniper I stole from this Bonsai Bark article: http://bonsaibark.com/page/97/

a2
Image does not belong to me

I decided windswept would be the way to go and went on with the plan. In order to convey this image and to perpetuate the windswept quality throughout the whole tree I wired the tree with an imaginary wind in mind. In reference to images of my trees imagine a wind blowing from right to left. This means that any growth initiating towards the right, up, or down, would be swept back and consequently wired in the opposite direction. I tried to follow this pattern as much as possible throughout the entire tree to create better cohesion.

On a side note, the best times to wire junipers is generally in the winter. Because of the reduced flow of sap, bark is less turgid and constricts around the branch more tightly. Meaning that when wiring the bark is less inclined to split. In the below image the cambium of that branch split a good deal. It may not be necessary but I decided to treat it as a graft and put a little baggy on it to ensure I don’t lose the branch.

20170311_141055
Growth exiting right side is swept under the branch to the left
20170311_155943
Foliage is kept in same orientation throughout the entire tree
20170311_141200
Same idea as in first image

Because the lower large trunk was nearly horizontal I opted for an angle that at least to me, would provide more realistic movement. I used guy wires to maximize my bends on the large trunk while the larger wire and raffia proved sufficient in bringing the top trunk down. All growth on the right side of the tree, although minimal, was removed and jinned. Any super leggy branches were jinned as well and even wired with the same aforementioned movement.

20170311_131922
progress picture

I cleaned up the apex and jinned any excess branching. I still have trouble capturing depth in my pictures and the overlay of branching can create clutter on a flat image. Here are shots of the finished tree in different lighting.

20170311_141038 (1)

The back of tree needs to fill in and after more growth I can continue to refine the foliage. The mid section does look a bit chaotic but will look better in successive stages of refinement.

Next year I will begin work on the root ball to accommodate the angle change and maybe a new pot. I’m thinking of adding shari on the backside and should fit well with the windswept design. Here is a rough virt of what I have in mind.

windswept kishu

All in all I am satisfied with the styling but will listen to any suggestions or critique (hopefully not too negative) anyone has to offer. Working on this tree really tested my creativity and gave me lots of practice on styling junipers.

I hope you’ve enjoyed this post and if you are so inclined, you can subscribe too!